Tweet
Motherboard description
* Motherboard manufacturer's name: MSI MS-7174
* HP/Compaq name: Graphite-GL8E
CPU/Processor
* Socket: 775
* Supports the following processors
o Pentium 4 600 series
o Pentium 4 with HT
o Celeron D
Front-side bus (FSB)
* 800 MHz (Pentiums)
* 533 MHz (Celeron D)
Chipset
* Northbridge: i915GV
* Southbridge: ICH6
BIOS features
* The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral devices and expansion cards of the board automatically.
* The mainboard provides a Desktop Management Interface (DMI) function which records your mainboard specifications.
Form factor
* Micro-ATX form factor: 9.6 in x 9.6 in
Memory
* Dual-channel memory architecture
* 2 x 240-pin DDR2 DIMM sockets for up to 2 GB non-ECC DDR2 533/400 SDRAM
* Maximum HP/Compaq approved memory is 2 GB
Expansion slots
* Three PCI
Video graphics
* Integrated
Serial ATA
* 2 SATA connectors
* Each connector supports 1 serial ATA-150 disk drive
Onboard audio or audio card Integrated Intel High Definition(TM) audio (Azalia)
*
Realtek ALC 880 CODEC
*
THX certification support
*
8-channels for Full Dolby 5.1/6.1/7.1 surround sound support with Dolby Pro Logic IIx
Onboard LAN
* Intel 82562GT
* 10/100Mbps Fast Ethernet LAN controller
Back panel I/O
* One PS/2 mouse port
* One PS/2 keyboard port
* One VGA (monitor)
* One Parallel
* Four USB (2.0)
* One IEEE 1394a
* One RJ-45 networking port
* Six audio ports support 8-channel Azalia audio codec
* One S-video out
* One SPDIF in/out
Internal connectors
* One 24-pin ATX power connector
* One 4-pin 12V ATX power connector
* One IDE connector
* Two SATA connectors
* One floppy drive connector
* CPU fan connector
* PC fan connector (also known as duct or chassis fan)
* PC indicator LEDs / power switch / reset button connector
* Optical drive audio input
* Auxilliary audio input (may be used for line input)
* Front panel headphone and microphone connector
* Two USB headers supporting up to 4 additional ports or devices
* One IEEE 1394a header supporting one 1394a port
NOTE: Motherboard specifications are subject to change without notice.
Motherboard layout and photos
Figure 1: layout
Figure 2: Photograph
Figure 3: Backplate
1 - PS/2 mouse port. This port is for a PS/2 mouse.
2 - Parallel port. The mainboard provides a 25-pin female centronic connector as LPT. A parallel port is a standard printer port that supports Enhanced Parallel Port (EPP) and Extended Capabilities Parallel Port (ECP) mode.
3 - 1394 port (Optional). The mainboard provides two 1394 pin headers that allow you to connect optional IEEE 1394 port.
4 - LAN (RJ-45) port. The mainboard provides 1 standard RJ-45 jack for connection to single Local Area Network (LAN). This LAN enables data to be transferred at 100Mbps or 10Mbps. You can connect a network cable to it.
5 - Subwoofer Speaker Out.
6 - Line In.
7 - Rear Speaker Out.
8 - Line Out.
9 - MIC.
10 - Side Surround Out.
11 - USB 2.0 ports. The mainboard provides an OHCI (Open Host Controller Interface) Universal Serial Bus root for attaching USB devices such as keyboard, mouse or other USBcompatible devices. You can plug the USB device directly into the connector..
12 - VGA Port. The mainboard provides a DB 15-pin female connector to connect a VGA monitor.
13 - SPDIF out.
14 - SPDIF in.
15 - PS/2 keyboard port. This port is for a PS/2 keyboard.
Clearing the CMOS settings
CAUTION: Do not change any jumper setting while the PC is running. Damage to the motherboard may result.
Clear RTC RAM (3-pin CLRTC)
There is a CMOS RAM on board that has a power supply from an external battery to keep the PC configuration data. With the CMOS RAM, the PC can automatically start OS every time it is turned on. If you want to clear the PC configuration, use the JBAT1 (Clear CMOS Jumper) to clear data. Follow the instructions below to clear the data.
1.
To clear CMOS settings, set jumper JBAT1 to pins 2-3.
Warning: Do NOT start the PC with this jumper set to pins 2-3.
2.
Wait 10 seconds and then return the jumper to pins 1-2. You may now restart the PC.
CAUTION: Except when clearing the RTC RAM, never remove the jumper from the default position. Removing the jumper causes PC start failure!
Clearing the BIOS password
This motherboard has a jumper to disable password checking if you've forgotten it.
CAUTION: Do not change any jumper setting while the PC is running. Damage to the motherboard may result.
1.To disable BIOS password checking, remove the jumper JPWD1. You may now start the computer, enter BIOS setup, and change or erase the password.
2.To enable BIOS password checking, replace the jumper on pins 1-2.
CAUTION: Except when clearing the RTC RAM, never remove the jumper from the default position. Removing the jumper causes PC start failure!
มันเป็นของ HPอะคับแต่คือ boardตัวในรูปเลยขอบคุณล่วงหน้าคับแรมด้วยคับ
Comment