Tweet
DELTA 700WATT DPS-700FB-1 POWER SUPPLY, DPS-700FB-1 A
Specifications:
* +5 V and +3.3 V total output not to exceed 140 W
* Maximum combined load on +12 V is 50 A
* Maximum total continuous output power is 700 W
Input 100 - 127 V ~ 12 A; 47 Hz - 63 Hz
Autorange 200 - 240 V ~ 6 A; 47 Hz - 63 Hz
# Output +3.3 V / 24.0 A
# +12 V1 / 18.0 A
# +12 V2 / 16.0 A
# +12 V3 / 18.0 A
# +12 V4 / 18.0 A
# +5 VSB / 3.0 A
# +5.0 V / 24.0 A
# -12 V / 0.5 A
These are the 2 × 3 add-in card power connectors. Some video or controller cards require a power supply in addition to that provided by the slot they are installed in.
The following graphic shows the connectors from another angle.
These are the drive power connectors. The 4-pin connectors are used to power drives such as hard drives, optical drives. ZIP drives, or tape backup units. The smaller connector is for a floppy disk drive.
The power supply has one extra drive power connector separate from these three and with a longer cable.
This is the 2 × 12 main power connector for the computer motherboard. This connector is keyed for proper connection and has a clip to ensure a secure connection.
This is the 2 × 4 processor power connector. This connector is keyed for proper connection and has a clip to ensure a secure connection.
These are the three Serial ATA (SATA) power connectors. These are used to power SATA devices such as hard drives.
The following graphic shows the connectors from a different angle.
ทีมา http://www.ascendtech.us/itemdesc.as...079R01&eq=&Tp=
เช็คให้ที่ใครดูเป็น วัตต์เต็ม หรือไม่เต็ม
แล้วมัน redundancy หรือเปล่า
Specifications:
* +5 V and +3.3 V total output not to exceed 140 W
* Maximum combined load on +12 V is 50 A
* Maximum total continuous output power is 700 W
Input 100 - 127 V ~ 12 A; 47 Hz - 63 Hz
Autorange 200 - 240 V ~ 6 A; 47 Hz - 63 Hz
# Output +3.3 V / 24.0 A
# +12 V1 / 18.0 A
# +12 V2 / 16.0 A
# +12 V3 / 18.0 A
# +12 V4 / 18.0 A
# +5 VSB / 3.0 A
# +5.0 V / 24.0 A
# -12 V / 0.5 A
These are the 2 × 3 add-in card power connectors. Some video or controller cards require a power supply in addition to that provided by the slot they are installed in.
The following graphic shows the connectors from another angle.
These are the drive power connectors. The 4-pin connectors are used to power drives such as hard drives, optical drives. ZIP drives, or tape backup units. The smaller connector is for a floppy disk drive.
The power supply has one extra drive power connector separate from these three and with a longer cable.
This is the 2 × 12 main power connector for the computer motherboard. This connector is keyed for proper connection and has a clip to ensure a secure connection.
This is the 2 × 4 processor power connector. This connector is keyed for proper connection and has a clip to ensure a secure connection.
These are the three Serial ATA (SATA) power connectors. These are used to power SATA devices such as hard drives.
The following graphic shows the connectors from a different angle.
ทีมา http://www.ascendtech.us/itemdesc.as...079R01&eq=&Tp=
เช็คให้ที่ใครดูเป็น วัตต์เต็ม หรือไม่เต็ม
แล้วมัน redundancy หรือเปล่า
![:[HARDMAN]:](https://cdn2.overclockzone.com/forums/core/customavatars/thumbs/avatar82559_15.gif ":[HARDMAN]:"){kind=avatar}
Comment