Announcement

Collapse
No announcement yet.

แพ็ทเทียร์...ใครเคยใช้ มาระบายความร้อนCPUบ้างครับ

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • แพ็ทเทียร์...ใครเคยใช้ มาระบายความร้อนCPUบ้างครับ

    รูปร่างของแพ็ทเทียร์นะครับ ประมาณ 1 ตาราง นิ้ว
    การทำงานของแพ็ทเทียร์ นะครับเมื่อป้อนไฟ 12V DC แล้ว ด้าน 1 จะเย็นมากๆๆประมาณ 10 องศาC แล้วอีกด้านจะอุ่นๆๆ ผมเคยมีแนวคิดถ้านำด้านที่เย็น มาระบายความร้อนที่ CPU แล้วจะมีผลเสียต่อ CPU หรือป่าวครับ (เพราะว่าด้านที่เย็น เย็นมากจริงๆ ผมใช้นิ้วแตะเพื่อระบายความเย็นกลับเป็นว่า นิ้วผมชาไปเลย) ใครอยากลองทดสอบแพ็ทเทียร์ ก็PMมานะครับ ขอเฉพาะที่ขอนแก่นครับ

  • #2
    น่าสนครับ แต่ไม่กล้าลอง ...
    ถ้าดีจริงเขาคงใช้กันเกลื่อนแล้วหละครับ
    GLORIOUS PC MASTER RACE
    May your frame rate be mighty and your draw distance far.

    Comment


    • #3
      ไม่รู้จักอะครับ เพิ่งเคยได้ยินนี่เอง

      Comment


      • #4
        มาเพิ่มให้ครับ เพราะพึ่งเข้าไปดูที่เว็ป overclock.net มาครับ เขามี forums ของ TEC โดยเฉพาะเลย


        เย็นมากหน่ะเย็นจริงครับ แต่จะแก้ปัญหาเรื่องเกล็ดน้ำแข็ง - หยดน้ำ ยังไงครับ
        ผมไม่แนะนำให้ต่อกับHardware โดยตรงนะครับ
        ผมเห็นที่เมืองนอกเขาเอา TEC(ชื่อของมัน) <ส่วน เพวเทียร คือชื่อคนคิดค้นครับ> นี่แหละครับ เอาไปจ่อกับ rad ของ lcs ทั้งหลาย ให้น้ำเย็นไหลเข้า CPU แทน ไม่งั้นคุมไม่ได้ครับ เรื่องความเย็น
        GLORIOUS PC MASTER RACE
        May your frame rate be mighty and your draw distance far.

        Comment


        • #5
          เคยอ่านเจอใน Chip ฉบับเก่าๆ ว่ามันเป็นระบบระบายความร้อนที่มีมานานแล้วใช้ไฟฟ้าเป็นตัวนำความร้อน
          เวลาใช้งานด้านหนึ่งจะเย็นติดลบอีกด้านจะร้อนมากเลยไม่นิยมนำมาใช้น่ะ
          Last edited by danero; 27 Jan 2008, 21:26:09.

          Comment


          • #6
            The Eliminator - Water Cooling and TEC Technology Combined

            อยากได้เหมือนกันครับ แต่ราคาไม่ใช่ย่อยเลยทีเดียว และต้องสั่งจากนอกอย่างเดียว HWbot ที่ผมโดนแซงก็เพราะเจ้านี่ T^T

            Comment


            • #7
              A Brief History

              Early 19th century scientists, Thomas Seebeck and Jean Peltier, first discovered the phenomena that are the basis for today's thermoelectric industry. Seebeck found that if you placed a temperature gradient across the junctions of two dissimilar conductors, electrical current would flow. Peltier, on the other hand, learned that passing current through two dissimilar electrical conductors, caused heat to be either emitted or absorbed at the junction of the materials. It was only after mid-20th Century advancements in semiconductor technology, however, that practical applications for thermoelectric devices became feasible. With modern techniques, we can now produce thermoelectric “modules” that deliver efficient solid state heat-pumping for both cooling and heating; many of these units can also be used to generate DC power in special circumstances (e.g., conversion of waste heat). New and often elegant uses for thermoelectrics continue to be developed each day.

              A Closer Look

              A typical thermoelectric module consists of an array of Bismuth Telluride semiconductor pellets that have been “doped” so that one type of charge carrier– either positive or negative– carries the majority of current. The pairs of P/N pellets are configured so that they are connected electrically in series, but thermally in parallel. Metalized ceramic substrates provide the platform for the pellets and the small conductive tabs that connect them. The pellets, tabs and substrates thus form a layered configuration. Module size varies from less than 0.25" by 0.25" to approximately 2.0" by 2.0". Thermoelectric modules can function singularly or in groups with either series, parallel, or series/parallel electrical connections. Some applications use stacked multi-stage modules.



              figure 1

              Cooling, Heating: When DC voltage is applied to the module, the positive and negative charge carriers in the pellet array absorb heat energy from one substrate surface and release it to the substrate at the opposite side. The surface where heat energy is absorbed becomes cold; the opposite surface where heat energy is released, becomes hot. Using this simple approach to “heat pumping”, thermoelectric technology is applied to many widely-varied applications– small laser diode coolers, portable refrigerators, scientific thermal conditioning, liquid coolers, and beyond.

              Power Generation: Employing the effect which Seebeck observed, thermoelectric power generators convert heat energy to electricity. When a temperature gradient is created across the thermoelectric device, a DC voltage develops across the terminals. When a load is properly connected, electrical current flows. Typical applications for this technology include providing power for remote telecommunication, navigation, and petroleum installations.

              A Comparison of Cooling Technologies

              The flow of heat with the charge carriers in a thermoelectric device, is very similar to the way that compressed refrigerant transfers heat in a mechanical system. The circulating fluids in the compressor system carry heat from the thermal load to the evaporator where the heat can be dissipated. With TE technology, on the other hand, the circulating direct current carries heat from the thermal load to some type of heat sink which can effectively discharge the heat into the outside environment.



              figure 2
              Each individual thermoelectric system design will have a unique capacity for pumping heat (in Watts or BTU/hour) and this will be influenced by many factors. The most important variables are ambient temperature, physical & electrical characteristics of the thermoelectric module(s) employed, and efficiency of the heat dissipation system (i.e., sink). Typical thermoelectric applications will pump heat loads ranging from several milliwatts to hundreds of watts.

              Thermoelectric Benefits

              The choice of a cooling technology will depend heavily on the unique requirements of any given application, however, thermoelectric (TE) coolers offer several distinct advantages over other technologies:

              • TE coolers have no moving parts and, therefore, need substantially less maintenance.

              • Life-testing has shown the capability of TE devices to exceed 100,000 hrs. of steady state operation.

              • TE coolers contain no chlorofluorocarbons or other materials which may require periodic replenishment.

              • Temperature control to within fractions of a degree can be maintained using TE devices and the appropriate support circuitry.

              • TE coolers function in environments that are too severe, too sensitive, or too small for conventional refrigeration.

              • TE coolers are not position-dependent.

              • The direction of heat pumping in a TE system is fully reversible. Changing the polarity of the DC power supply causes heat to be pumped in the opposite direction– a cooler can then become a heater!

              Design Calculation Tutorial

              Let's assume a solid-state electronic component requires cooling to improve performance and reliability. The component resides in an environment with a maximum ambient air temperature of 50&#176;C and dissipates 15 Watts. Cooling the component to 25&#176;C will improve performance and reliability.





              More at http://www.tellurex.com/cthermo.html
              Last edited by KiDMaioRKz; 27 Jan 2008, 15:46:27.
              GLORIOUS PC MASTER RACE
              May your frame rate be mighty and your draw distance far.

              Comment


              • #8
                ขอบคุณ ทุกท่านและทุกคำแนะนำครับ
                ขอขคุณครับ

                Comment

                Working...
                X