Announcement

Collapse
No announcement yet.

ขั้นตอนการ OC E7200 ไปที่ 4.1Ghz

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ขั้นตอนการ OC E7200 ไปที่ 4.1Ghz

    ผมไม่ได้มาสอนบอกก่อนครับ เพียงแต่หาข้อมูลมาให้ศึกษา
    ฉะนั้น อย่าถามผม เพราะผมก็มะรู้ครับ



    ตัวอย่างแรก

    ใช้บอร์ด GA-EP35C-DS3R
    CPU ตัวใหม่จาก INTEL C2D E7200 L2 3MB. 45n
    เดิมๆ ของ CPU ตัวนี้อยู่ที่ 2.5ghz ครับ โดยมีตัวคูณที่สูงสะใจที่ 9.5 x 266 = 2.5ghz
    รุ่นพี่อย่าง E7300 อีกด้วย พร้อมตัวคูณ 10 x 266 = 2.66Ghz ครับ ซึ่งดูแล้วตัวคูณน่าจะเป้นจุดสนใจที่สุดสำหรับ CPU ตระกูลนี้ครับ เพราะอย่างน้อยถ้าโดน FSB Wall ก็เอา Ghz เข้าข่มละกันด้วยตัวคูณที่สูงมาก ระดับ 9-10 หุหุ.....

    เอาล่ะครับ สำหรับ E7200 ตัวนี้ผมเทสที่ความเร็วที่ Overclock แล้วไปที่

    - 9.5x433 = 4.11Ghz Vcore 1.600V Bios Set แต่ใน Window Droop ไปเหลือ 1.55v ครับดูจาก CPU-Z ตกเยอะเหมือนกันบอร์ดรุ่นนี้
    - Memory Config นั้น ก็ปรับไปที่ Strap 266 และวิ่ง 433Mhz แบบ 1:1 เท่าบัส CPU ปรับ CL 4-4-4-12-25
    - ในการทดสอบที่เหลือ Auto ครับ
    - ส่วนไฟจุดอื่นๆ นั้นผมเพิ่มแต่ VMCH สุดบอร์ดเลยครับที่ +0.3V นอกนั้นปรับ Normal ทั้งหมด

    เครดิต คุณ audigy


    ตัวอย่างที่ 2

    Advanced BIOS Features
    CPU Enhanced Halt (C1E) Disable
    CPU Thermal Monitor 2(TM2) Disable
    CPU EIST Function (Note) Disable

    MB Intelligent Tweaker(M.I.T.)
    CPU Host Clock Control Enabled
    CPU Host Frequency (Mhz) 422
    PCI Express Frequency (Mhz) 100
    System Memory Multiplier (SPD) 2.0 (You want it as close to 800, but with your FSB at 422, it will be exactly 844)

    System Voltage Control
    DDR2 OverVoltage Control: +0.2v (default is 1.8v, but the ram can run 1.8v-2.0v accoriding to G.Skill)
    PCI-E OverVoltage Control [Normal]
    FSB OverVoltage Control +0.1v
    (G)MCH OverVoltage Control +0.2v
    CPU Voltage Control 1.30v - 1.35v (this is your CPU's vcore, it might need less then 1.35v)

    ตัวอย่างที่ 3

    Boot into bios and go to advanced:

    Under Jumper free Settings:

    A1 overclocking set to manual

    CPU frequency to 400 (higher later if that works}
    Performance set to “Standard.”
    PCI Express frequency to 100
    PCI clock synchronization to 33
    Memory Voltage to 2.10
    CPU Core to 1.3-1.45v depending on overclock speed
    FSB termination voltage to 1.4-1.5 whichever works
    MCH voltage to 1.75
    ICH voltage to 1.05

    Hit ESC and go down to “CPU Configuration”

    Modify Ration: Disable
    Max CPUID: Disable
    Execute Disable Function: Disable
    CPU Thermal Control: Disable
    Virtualization: Disable

    Hit ESC and go to "Chipset"

    Dram CAS to 5
    Ras to 5
    Ras to Cas 5
    Dram Ras activate precharge [15]
    Dram write recover to 5
    Dram ECC: Disable
    Hyper Path 3: Disable
    Dram throttling: Disable
    Memory remap: Disable
    Last edited by ittiphol; 24 Oct 2008, 10:10:52.

  • #2


    การตั้งค่าอย่างละเอียด บอร์ดไรไม่รู้ งง

    DRAM Timing
    - Enhance Data transmitting: Fast
    - Enhance Addressing: Fast
    - T2 Dispatch: Enabled

    Clock Setting Fine Delay
    Ch1 Clock Crossing Setting: More Agressive
    - DIMM 1 Clock fine delay: Current
    - DIMM 2 Clock fine delay: Current
    - Ch 1 Command fine delay: Current
    - Ch 1 Control fine delay: Current

    Ch2 Clock Crossing Setting: More Agressive
    - DIMM 3 Clock fine delay: Current
    - DIMM 4 Clock fine delay: Current
    - Ch 2 Command fine delay: Current
    - Ch 2 Control fine delay: Current

    Ch1Ch2 CommonClock Setting: More Agressive

    Ch1 RDCAS GNT-Chip Delay: Auto
    Ch1 WRCAS GNT-Chip Delay: Auto
    Ch1 Command to CS Delay: Auto

    Ch2 RDCAS GNT-Chip Delay: Auto
    Ch2 WRCAS GNT-Chip Delay: Auto
    Ch2 Command to CS Delay: Auto (where cpuz sees 1T or 2T SETTING)

    CAS Latency Time (tCL):5
    RAS# to CAS# Delay (tRCD):5
    RAS# Precharge (tRP):5
    Precharge Delay (tRAS):18
    All Precharge to Act: 5
    REF to ACT Delay (tRFC): 55
    Performance LVL (Read Delay) (tRD):8

    Read delay phase adjust: Enter

    Ch1 Read delay phase (4~0)
    - Channel 1 Phase 0 Pull-In: Enabled
    - Channel 1 Phase 1 Pull-In: Enabled
    - Channel 1 Phase 2 Pull-In: Enabled
    - Channel 1 Phase 3 Pull-In: Enabled
    - Channel 1 Phase 4 Pull-In: Enabled
    Ch2 Read delay phase (4~0)
    - Channel 2 Phase 0 Pull-In: Enabled
    - Channel 2 Phase 1 Pull-In: Enabled
    - Channel 2 Phase 2 Pull-In: Enabled
    - Channel 2 Phase 3 Pull-In: Enabled
    - Channel 2 Phase 4 Pull-In: Enabled

    MCH ODT Latency: 8
    Write to PRE Delay (tWR): 14
    Rank Write to Read (tWTR): 11
    ACT to ACT Delay (tRRD): 3
    Read to Write Delay (tRDWR): 8
    Ranks Write to Write (tWRWR): 5
    Ranks Read to Read (tRDRD): 5
    Ranks Write to Read (tWRRD): 8
    Read CAS# Precharge (tRTP): 3
    ALL PRE to Refresh: 3

    to get my cpu to 500fsb, i pretty much followed the anandtech article for my mobo, then adjusted volts and gtl slightly to stabilize it. it worked pretty well as a starting point.
    i will be switching back to the asus as my every day rig and make the dfi my bench board. this is an lt w/ ut bios *there is not any diff between the 2 except for stock cooling*

    Comment


    • #3
      ไป4ghz ไฟเยอะขนาดนั้นเลยหรือครับ ของผมที่3.9ไฟแค่ 1.375 เอง ดรอบแล้วประมาณ1.34

      Comment


      • #4
        ผมก็ไม่รู้นะ มันน่าจะปรับๆ กันได้นะ เอาเป็นแนวทางครับผม

        Comment


        • #5
          4.3 ผม 1.55 เองงับ

          Comment


          • #6
            Originally posted by mewonline View Post
            ไป4ghz ไฟเยอะขนาดนั้นเลยหรือครับ ของผมที่3.9ไฟแค่ 1.375 เอง ดรอบแล้วประมาณ1.34
            ของผมทำไม ได้ 3.5 ไฟ 1.42 จ่ายจริง 1.4....

            Comment


            • #7
              รับไฟมหาโหดเลยวุ้ย ....

              Comment


              • #8
                มาจดๆ

                Comment


                • #9
                  เหอๆๆ เปิดกระทู้เองเลยวุ้ย

                  Comment


                  • #10
                    ใหนวะ กุอยากเห็น P5KPL 5Ghz orthos 10 ผ่าน

                    Comment


                    • #11
                      ของแรง ๆ

                      Comment


                      • #12
                        Originally posted by maxx2007 View Post
                        ของผมทำไม ได้ 3.5 ไฟ 1.42 จ่ายจริง 1.4....
                        อันนี้ที่ 400X9=3.6 ครับ

                        Comment


                        • #13
                          มาเอาความรู้ ครับ

                          Comment


                          • #14
                            ลดไฟหน่อย
                            ลดภาวะโลกร้อน

                            Comment


                            • #15
                              จะหามาเพิ่มเติมอีก

                              ตัวเราไม่ค่อยรู้ แต่เจอจะหามาแชร์ครับ

                              Comment

                              Working...
                              X